Tester

Tester Day Shift: Monday through Thursday 5:00AM to 3:30PM Testing electronic components of Nacelle before final assembly occurs Responsibilities Test safely, according to all procedures, is the #1 priority as there are high hydraulic pressures and high voltages in test Control and test an assembled, or pre-assembled product in production; make quality control of the product to ensure no failures pass through to the next level and/or supplier Verify adherence to Vestas quality and testing standards before allowing product to takt to next operation Perform assembly / process work in operation for which he/she is responsible for, as needed; normally will be perform non-standard work and will cover operations in the event of absences Problem-solving by trying to diagnose test failure issues Point of contact within operation for process/product engineering changes Ensure NCR reports is made, as regarding product/assembly not meeting Vestas quality specifications Inspect product to determine compliance with order specifications, company's quality control system for compliance QDA entry; stamp mark of approval or rejection with QDA on product and write report Provide customer service by responding to requests for service and assistance Listen and obtain clarification; responds well to questions Teamwork - gives and welcomes feedback Ethics - Upholds organizational values Follows organizational policies and procedures Demonstrate accuracy and thoroughness; Apply feedback to improve performance Observe safety and security procedures; determine appropriate action beyond guidelines; report potentially unsafe conditions; use equipment and materials properly Other duties as assigned Education, Training, and Skills Required Journeyman or Master Electrical license and 4 years' hands‑on experience OR documented electrical education (i.e. Associates degree in Electrical Engineering, Trade school certificate of graduation, Bachelor's degree in electrical engineering) and 4 years' hands‑on experience OR documented military‑equivalent technical training with electrical system, (i.e. Avionics, Power Production, Civil Engineering) and 4 years' hands‑on experience. Note: experience must be with industrial or commercial electrical equipment including maintenance and troubleshooting 3 phase systems and controls Annual refresher courses in electrical and hydraulic safety training Knowledge of Manufacturing software and Spreadsheet software Ability to add, subtract, multiply, and divide in all units of measure, using whole numbers, common fractions, and decimals Ability to compute rate, ratio, and percent and to draw and interpret bar graphs Ability to apply common sense understanding to carry out instructions furnished in written, oral, or diagram form Ability to deal with problems involving several concrete variables in standardized situations Essential Functions Ability to read, write and comprehend simple instructions, short correspondence, and memos Ability to observes safety and security procedure Regular and reliable attendance Education, Training, and Skills Required Must be able to pass an Electrical Aptitude Test Annual refresher courses in electrical and hydraulic safety training Safety focused mindset Your positive attitude will contribute to your ability to work in a team environment, while being motivated and taking initiative in daily tasks You can identify solutions to issues with process of elimination At least one year of wing experience or 2‑3 years of experience in an applicable background, including mechanical, hydraulic, and electrical troubleshooting experience Knowledge of Manufacturing software and Spreadsheet software Ability to add, subtract, multiply, and divide in all units of measure, using whole numbers, common fractions, and decimals Ability to compute rate, ratio, and percent and to draw and interpret bar graphs Ability to apply common sense understanding to carry out instructions furnished in written, oral, or diagram form Ability to deal with problems involving several concrete variables in standardized situations Ability to comprehend electrical and hydraulic schematics with European symbols Low voltage troubleshooting - 24V PLC experience Network experience - Wi-Fi and Fiber optics Basic knowledge of hydraulic valves Physical Demands The physical demands described here are representative of those that must be met by an employee to successfully perform the essential functions of this job. Reasonable accommodations may be made to enable individuals with disabilities to perform the essential functions. While performing the duties of this job, the employee is frequently required to stand; walk; use hands to finger, handle, or feel; reach with hands and arms; climb or balance; stoop, kneel, crouch, or crawl and talk or hear. The employee is occasionally required to sit. The employee must occasionally lift and/or move up to 30 pounds. Specific vision abilities required by this job include close vision, peripheral vision, depth perception and ability to adjust focus. Work Environment The work environment characteristics described here are representative of those an employee encounters while performing the essential functions of this job. Reasonable accommodations may be made to enable individuals with disabilities to perform the essential functions. While performing the duties of this Job, the employee is frequently exposed to moving mechanical parts. The employee is occasionally exposed to high, precarious places, risk of electrical shock and vibration. The noise level in the work environment is usually moderate. This Job Description is not intended to be a comprehensive list of the duties and responsibilities of this position, and the duties and responsibilities of this position may change without notice at the Company's sole discretion. Salary Range $30.00-$39.00 #J-18808-Ljbffr